BOILER PARTS / CLEVELAND, OHIO
Boiler Parts Sales and Service in Cleveland, OH
Boiler parts sales Cleveland plants can count on start with a shelf, not a catalog. D. B. Johnsen Co. has stocked commercial and industrial boiler parts in Richfield since July 1958, about twenty five minutes south of downtown, and we sell to end users, mechanical and piping contractors, and consulting engineers across the city. No residential work.
A lot of Cleveland boiler rooms are older than the people running them. Firetube units in Midtown warehouses. Watertube boilers behind the hospital campuses in University Circle. Low pressure steam plants that came off the downtown district loop decades ago and never got fully documented. Parts for that equipment are hard to find at a general supply house. For us they are a normal Tuesday.
Boiler Parts Sales in Cleveland Start With the Nameplate
Most boiler parts sales Cleveland buyers bring us begin with a phone photo of the boiler nameplate. Make, model, and serial number. Those three lines separate a control that bolts right in from one that almost fits, and almost is how a one-day outage turns into three. With the plate in hand our counter staff can match the part from our boiler parts inventory or order it direct from the factory.
If you searched boiler parts sale near me from a plant in the Flats and got a page of furnace filters, call us instead. We stock the industrial side only. In-stock parts ship UPS the same day, and for units that have outlived their manufacturer we also keep overstock and older-model parts that a new-parts distributor will not have.
Burner Controls and Flame Safeguards for Cleveland's Older Steam Plants
Plenty of burners in Cleveland are still running on relay-based programmers that were discontinued before the current maintenance supervisor was hired. When one fails, there is no like-for-like replacement on any shelf. We cross the old unit over to a current flame safeguard, supply the scanner and wiring base it needs, and tell you up front what changes in the panel.
Burner parts and components wear on a schedule you can predict: diffusers, electrodes, ignition transformers, linkage, and blower motors. We carry the common ones. If you want the new control commissioned rather than just dropped in, our factory-trained service technicians set it up and run combustion on the same visit.
Feedwater, Deaerator and Economizer Parts for Cleveland Process Steam
Cleveland draws its water from Lake Erie through intake cribs set miles offshore. It is decent water to drink. It still carries enough calcium, magnesium, and dissolved oxygen that boiler makeup has to be softened, deaerated, and chemically treated, and the hardware that does that work wears out. The parts we sell most into Cleveland process steam plants:
- Boiler feedwater system parts: level controls, makeup valves, strainers, and pump seals
- Deaerator parts for spray and tray units, including spray valves and vent condensers
- Economizer parts and heat recovery and HRSG parts, sourced through the manufacturers we represent
- Boiler pumps for feed and condensate return service
Fuel Oil Pumps, Day Tank Components and Fuel Oil Controls for Cleveland Standby Firing
Hospitals, labs, and larger plants around Cleveland often keep oil as a backup fuel on dual-fuel burners. That oil system may sit idle for most of a year, and the first time anyone finds out a fuel oil pump has seized is the day the gas gets curtailed. We supply fuel oil pumps, day tank components such as level switches and transfer pump parts, and fuel oil controls including solenoid valves and pressure regulators.
If the oil side cannot be brought back in time, our boiler repair crews can work the problem on site, and a temporary rental boiler can carry the load while they do.
Boiler Tubes and Safety and Relief Valves Ahead of Cleveland's Lake-Effect Season
The first real lake-effect storm usually reaches the east side in November, and it tends to arrive overnight. That is when a boiler idle since spring gets asked to carry full load and a tired tube lets go. We supply boiler tubes cut to the unit and the gaskets, hand-hole plates, and refractory that go with a retube.
Safety and relief valves are a different conversation. A relief valve gets replaced with one of the same set pressure and relieving capacity, stamped for the service, not adjusted or rebuilt by guesswork. Where a repair touches the pressure vessel itself, our welders work under ASME R-Stamp certification, and you can read more about that on our R-Stamp repair page.
Why Cleveland Plant Engineers Have Bought Boiler Parts From Us Since 1958
Our counter sits on Brecksville Road in Richfield. Head south out of the city on I-77 and you are here in about twenty five minutes, which is why plenty of Cleveland maintenance supervisors drive down for will-call rather than wait on freight.
We answer calls and quote requests within two to four hours, and the same number reaches our 24-hour emergency line after the counter closes at five. Because we also sell new steam and hot water boilers, the people quoting your part know how the whole boiler is supposed to behave, not just the part number in front of them.
That is the difference boiler parts sales Cleveland customers notice first. Someone picks up, and they know what a low water cutoff is.
Request a quotePARTS SERVICE AREA
Boiler Parts Coverage From Cleveland to Lakewood, Parma and Euclid
Our boiler parts sales Cleveland coverage reaches the whole city, from Collinwood and Slavic Village to the industrial streets off Harvard Avenue and the warehouses along the Cuyahoga in the Flats. Parts also go out daily to Lakewood, Parma, Euclid, Independence, Garfield Heights, and Cuyahoga Heights.
Whether you searched boiler parts sale near me from Lakewood or from a boiler house off Broadway Avenue, the order ships from the same Richfield shelf. Closer to our shop, see boiler parts sales in Richfield, or head south for parts support in Akron.
Shipped and sold from 4900 Brecksville Road, Richfield, OH 44286. See the full service area.
Boiler parts sales in other cities: Richfield · Akron · Canton · Toledo
BOILER PARTS FAQ
Boiler Parts Questions From Cleveland Maintenance Supervisors
Do you sell boiler parts to Cleveland facilities that did not buy their boiler from you?
Yes. We match parts for any make and model, including units we never sold. Send a photo of the nameplate with the make, model, and serial number and we will identify the right component.
How fast can a part reach a plant in Cleveland?
For boiler parts sales Cleveland orders, in-stock parts ship UPS the same day you call. If you would rather pick up, our will-call counter in Richfield is about twenty five minutes south of downtown on I-77.
Can you replace an obsolete flame safeguard on an older burner?
Yes. When the original programmer is no longer made, we cross it over to a current flame safeguard and supply the scanner, wiring base, and any other parts the conversion needs. Our service technicians can install and commission it if you want.
Do you carry deaerator and feedwater system parts?
We supply feedwater system parts such as level controls, makeup valves, and pump seals, along with deaerator parts for spray and tray units. Larger heat recovery and economizer components are sourced through the manufacturers we represent.
What should I have ready before I call about a boiler part?
The make, model, and serial number from the boiler nameplate, plus the part description or the symptom you are seeing. A photo of the plate and of the failed part speeds things up. If you are not sure what failed, describe the symptom and we will work backwards from there.
Do you sell parts to mechanical and piping contractors working in Cleveland?
Yes. Contractors and consulting engineers are a large share of our customers, along with plant and facility end users. We do not sell to residential customers.
How should a safety or relief valve be replaced?
With a valve of the same set pressure and relieving capacity, stamped for the service it will see. Read the data off the existing valve tag and we will match it. Relief valves should never be adjusted or modified in the field to make a different valve fit.
What if a part fails after hours?
Call the same number, 330-659-9295. The counter is open Monday through Friday from 8:00am to 5:00pm, and our 24-hour emergency service line covers nights, weekends, and holidays.
LINES WE REPRESENT
Also representing: Century Controls.